NEW Site Activated! Please register there:

  • If you are registered user on this site,- on new site finish registration with SAME email!
  • On new site Username must be from 4 to 9 characters, alphanumeric, latin only! (no spaces, special character allowed)!
    So, if you have your old username different from this note - no problem! check new username/login!
  • After registration you will be able to transfer/migrate all your datas, balance etc.

  • Sort articles by: Date | Most Rates | Most Views | Comments | Alphabet
            Category: FAQs Cardsharing     Updated: 30-09-2013, 07:11 by dr.Freak     Views:     Comments: 2

    What is Cardsharing?

    Cardsharing is the ability of more than one receiver to operate using the same legitimate card. Generally, in this situation the receiver is connected to a computer. This acts as the host for the information. All of the other receivers who wish to access the information become clients. The clients are then able to access the unencrypted code via the host. Another facet of this system is that you can connect to more than one television. However, if you only have one receiver you will only be able to watch one channel at any given time. If you do want to use Cardsharing, you will have to purchase a subscription. A subscription will provide you with the codes, which will allow you to get a clear unencrypted picture. CCcam and receivers (e.g. Dreambox) are quickly becoming a popular way of getting satellite television. What Equipment do You Need to Make This System Work? You must have a receiver, which can run the CCcam protocol software. Additionally, you will need to have a satellite and have broadband. CCcam is a special piece of software that you will need to speak to a server. It is this software that will permit you to watch your programs uninterrupted. Every couple of seconds a signal is actually sent to your television, which needs to be decrypted. This is where the Cccam comes in. It can make certain that you are able to get the signal without the encryption. It is the unlocking key. This process should occur in a mere matter of milliseconds. However, there are providers who cannot do this correctly. If you are not using a server, which has a stable service you will experience either pixilation or freezes. Both of these effects will make watching anything virtually impossible. One of the most important things about installing CCcam is that you do it correctly. You are going to need to run a test on your Dreambox (or similar receiver). The test is designed to make certain that you have a fully functioning connection to the Internet. Satellite TV via CCcam and Cardsharing Linux based satellite receivers are the new wave of technology. There is a wide range of different makes and models currently available. What these receivers do is supply you with presentations through an IP service. Among the many receivers are the Dreambox 800, the Dreambox 600 and the Dreambox 500. Dreambox is not the only available receiver, there are others, including a number of clones. What do Receivers Actually do For You? You can get all of your favourite channels using the one box or receiver and a broadband connection. Basically, you will be able to view any program and/or channel that your satellite dish can access.

    What is Cardsharing?
    Key-Tags: Cardsharing FAQ

            Category: FAQs Cardsharing     Updated: 4-11-2015, 10:11 by dr.Freak     Views: 8892    Comments: 0
    • 0

    VU+ CCcam Setup

    For transferring the CCcam.cfg file into your VU+ SOLO or DUO, you need to use a FTP client. we suggest DCC!
    Note: to download and see the tutorial of Dreambox Control Center click here.
    Now, you just need to transfer the CCcam.cfg file into the /var/etc/ folder.
    Note: If you already have a CCcam.cfg file in that location, simply right click the file and click edit to put your C-lines in it and save the file.
    You can obtain the CCcam.cfg file from your service provider.
    Note: If you have your C-lines, click here to see how you can create the CCcam.cfg file yourself!
    Reboot your box and your CCcam Service will start working.
    VU+ CCcam Setup
    Key-Tags: Cardsharing, Cardsharing Settings, Cardsharing FAQ

            Category: FAQs Cardsharing     Updated: 4-11-2015, 10:08 by dr.Freak     Views: 5956    Comments: 0
    • 0

    Spiderbox CCcam Setup

    How to CCcam Setup for a Spiderbox via USB or remote control
    What do you need?
    1. USB Stick
    2. Valid cline
    3. Make a file and name it server.cfg and input all c-lines that we've emaled you like "C: serverIP 123port username password"; ... Save it!
    4. Copy the file server.cfg into the root of your USB Stick. Don't copy it in a specific folder otherwise the Spiderbox can't read the file
    5. Send the file to the Spiderbox
    6. Don't forget to enable your network, set it to DHCP
    7. Reboot the box and start CCcam
    CCcam setup via remote control:
    1. Go to Menu
    2. Enter your cline
    Host Name (IP address):
    User name:
    and APPLY.
    3. Restart the box
    4. Restart CCcam
    Spiderbox CCcam Setup
    Key-Tags: Cardsharing, Cardsharing Settings, Cardsharing FAQ

            Category: FAQs Cardsharing     Updated: 4-11-2015, 10:05 by dr.Freak     Views: 6192    Comments: 0
    • 0

    Skybox F5 CCcam Setup

    Format USB to FAT32 (on your pc)
    Turn on F5, let it boot up and put USB in the back
    Using remote control, press Menu ---> Network Local Settings . Press OK
    Select Camds Setup -->ok ---> CCcam Client Setup --> ok
    Select Update Files by USB
    Select CCcam.cfg (which is your Nline that is installed on the root of your USB)
    Then you have options to Add or Read or Cancel
    cccam.cfg example (without any additional line or space beforefirst line or after last line):
    C: cline1.server port user pass
    C: cline2.server port2 user pass
    C: cline3.server port3 user pass
    C: cline4.server port4 user pass
    C: cline5.server port5 user pass
    Skybox F5 CCcam Setup
    Key-Tags: Cardsharing, Cardsharing Settings, Cardsharing FAQ

            Category: FAQs Cardsharing     Updated: 4-11-2015, 09:56 by dr.Freak     Views: 7668    Comments: 0
    • 0

    Samsat HD 80 CCcam Setup

    Using USB and CCcam.cfg file:
    Menu / Tools / CAS  /CAS Options / network sharing / read cccam.cfg from usb/ok
    Manual Setup:
    1- Unplug the receiver from the internet
    2- Menu —> Tools—> CAS —> CAS Options —> FCAS Options —>Serial Port Use : disable GBOX SSSP and activate Morebox Protocol because you will also need to see his Morebox open channels…
    If FCAS is not activated, with the remote press MENU and then dial 2 0 2 0 then FCAS enabled OK
    3- Menu —> Tools—> CAS —> CAS Options —> FCAS Options —> Network sharing —-> ENABLE Network sharing !!!
    4- Menu —> Tools—> CAS —> CAS Options —> FCAS Options —> Network sharing —- > CCcam servers —> Server 1 (you can choose server 1 ou 2 ou 3 ou 4 ou 5 +++) :
    Fill CCCAM Server data in order using the remote control:
    – HOST
    – PORT
    – USER
    – PASS
    Now the configuration of TCP / IP data Samsat receiver :
    Menu —-> Congig Système —> Paramètres TCP/IP
    Now check:
    IP Auto = activated
    Auto Obtain DNS: disable
    Connect your Samsat HD80 to your ADSL Router with RJ45 cable …and wait 1 minute for the connection …!
    Samsat HD 80 CCcam Setup
    Key-Tags: Cardsharing, Cardsharing Settings, Cardsharing FAQ

            Category: FAQs Cardsharing     Updated: 4-11-2015, 09:54 by dr.Freak     Views: 6822    Comments: 0
    • 0

    Openbox and Skybox CCcam Setup

    1: Go into the main menu
    2: Select Network, enable your network and set the IP address to DHCP. Go back to network.
    3: Select "CCcam Client Setup" If you can not see CCcam setup in the menu jump to number 9
    4: If you have a cccam.cfg on your usb, we provide the CCcam.cfg file, ask for the full configured file from us to get all of our channels. Copy the CCcam.cfg file into the root folder from your USB stick. Do not copy the file in a specific folder.Select 'Update files by usb' if not, jump to number 10
    5: On new window, highlight 'CCcam.cfg', press green button on remote (ADD). This will place a tick by it, the press yellow button on remote (READ)
    6: Once finished, select 'Manage Config Files' and on new window select cccam.cfg again
    7: A new page comes up with your cline on it, press green button on remote to make it active (tick should appear by it) Exit out of all menus to tv and select a pay channel.. it should clear, if not go back into menu, select Network, then 'Network Setup', and turn DHCP 'off' by using arrow keys and then hitting apply.
    8: if channel still doesnt clear, reboot box and router by unplugging both from power and plugging back in (router first)
    9: if you cant see this option go to network and press 6666 this should bring up hiden menu or 8888
    10: for those who didnt create a cccam.cfg on their usb, you can add it manually..
    a] instead of update by usb on ccccam client setup, go directly to Manage Config Files and select CCcam.cfg from new window
    b] Press Blue button on remote
    c] your cline will look something like this>>> C: 12000 user pass
    d] ON add cline window, leave Protocol as CCcam
    e] Host: here you would enter portion of your cline using remote number buttons like you was sending a text
    f] Port: here you put 12000
    g] User, write 'user' here
    f: Password, write 'pass' here
    g] Press ok and go up to instruction number 7 OF CLINE SETUP

    Openbox and Skybox CCcam Setup
    Key-Tags: Cardsharing, Cardsharing Settings, Cardsharing FAQ

            Category: FAQs Cardsharing     Updated: 4-11-2015, 09:51 by dr.Freak     Views: 5822    Comments: 0
    • 0

    How to Setup CCcam on Technomate

    To install cccam on technomate boxes, Simple procedure has to be followed.
    First start up your box. Now follow these steps:
    -Press and hold the power button on your box front panel as it starts up
    -A number will appear in your front display and thats what your box IP Address ends in.
    Note: For example if the number is 5, then your box Ip Address is
    -Now with a web browser you need to connect to that IP by typing it in the browser.
    Note: Remember your PC/Laptop must be on the same IP range
    -On bottom right of this page you`ll see "CCcam Edit" under the menu Edit Email Config. Press "Click"
     -If it requests for password, type and proceed
    -Finally a field will appear with a button beside it called "Add Line"
    -Remember the line format you should enter is like this: C: server port user pass
    This was the standard procedure for installing CCcam on technomate boxes.
    How to Setup CCcam on Technomate
    Key-Tags: Cardsharing, Cardsharing Settings, Cardsharing FAQ

            Category: FAQs Cardsharing     Updated: 4-11-2015, 09:49 by dr.Freak     Views: 8209    Comments: 0
    • 0

    How to set cccam in Iris 9900 HD

    In this tutorial I will try to explain briefly how to configure cccam in 9900 Iris HD decoders, this shall be to use a different server.
    - To work in cccam protocol, make a file with this name: cccam_accounts.txt
    - Open the cccam_accounts.txt file with notepad. It should look something like this:
    – To insert our clines, we just edit the file cccam_acounts.txt replacing examples by data from our cline.
    – We should note that Iris 9900 only allowed a maximum of 10 clines.
    – Once you have filled the lines, save the document and put it in a pendrive.
    – We connect the pendrive in the deco.
    – Press the Menu button.
    – Press 6666.
    – We stand on the CCCam choice and mark it with the blue button to activate.
    cccam server
    – Press to OK and enter into CCCam.
    – We give the green button (File Explorer).
    Note: Here we may introduce our cline optionally manually with the remote.
    – Cccam_accounts locate the file and give it to Ok.
    – The clines will be charged and shall return back to the Settings screen CCCAM.
    – In No you can switch between clines that you have added and connected to each of them you have to just give Connect.
    – Status of each can see if it is active or not.
    How to set cccam in Iris 9900 HD
    Key-Tags: Cardsharing, Cardsharing Settings, Cardsharing FAQ

            Category: FAQs Cardsharing     Updated: 4-11-2015, 09:46 by dr.Freak     Views: 7964    Comments: 0
    • 0

    How to Make CCcam.cfg file

    Most of the satellite receiver boxes need CCcam.cfg file with your CCcam lines in it in order to work. Usually users ask their providers for a cfg file not knowing they can create it themselves. Doing this is pretty much easy and you only need to have your CCcam lines to put in it.

    First, create a simple text document.
    Put your CCcam lines in it. Make sure your Lines have the correct format according to your box.
    Note: usual format of CCcam lines is C: server port user pass
    Now from the top left side of your text document click File > Save As ....
    At the bottom there is a section called "Save As Type", change it to "All Files".
    Then from the top of it in "File Name" write CCcam.cfg and save it.
    Note: remember it`s vital that the first two C`s be in Caps Letters.
    Thats it, your CCcam.cfg file is ready to be used.
    How to Make CCcam.cfg file
    Key-Tags: Cardsharing, Cardsharing Settings, Cardsharing FAQ, CCcam

            Category: FAQs Cardsharing     Updated: 4-11-2015, 10:23 by dr.Freak     Views: 9062    Comments: 0
    • 0

    How to Install Dreambox Control Center


    Most of users are looking for a simple way to manage their receiver boxes via a flexible and well equipped FTP program. Some of you might use Filezilla or any other FTP clients but here we suggest you use the best FTP program which is designed for receiver boxes file management. You can manage or install your images, plugins or any other thing you want to upload or download from your box. One of the most common purposes is uploading/editing CCcam.cfg file.    First of all click here to download the zip folder containing DCC version 2.96

    Now extract the folder and open DCC. 



    Click DETAILS... for FULL Article! 

    How to Install Dreambox Control Center
    Key-Tags: Cardsharing, Cardsharing Settings, Cardsharing FAQ

            Category: FAQs Cardsharing     Updated: 4-11-2015, 09:41 by dr.Freak     Views: 6316    Comments:
    • 0

    Engel RS 4800 Y CCcam Setup

    1- Open notepad on pc.
    2- Enter your cccam lines 
    3- Save the file as CCcam_Newcamd.cfg
    4- Put the file in USB
    5- Insert the USB in your engel
    6- Menu / Update / Upgrade by USB
    7- update mode cccam_newcamd | cccam_newcamd.cfg file | ok
    8- flash Quemas
    9-Disable IKS (Menu / 7777 / IKS / DES)
    Engel RS 4800 Y CCcam Setup
    Key-Tags: Cardsharing, Cardsharing Settings, Cardsharing FAQ

            Category: FAQs Cardsharing     Updated: 4-11-2015, 09:39 by dr.Freak     Views: 6927    Comments:
    • 0

    Cloud Ibox 4 CCcam Setup

    1. Stick on a clone safe image
    2. Do your basic setup/ forget the channel scan say you will di it later manuly
    3. Goto autoboquets hit advanced settings fill in the sections and save. do a scan let it do its thing this will automaticly create your channel list. then set it to do a update evreyday
    4. Download filezilla to your pc
    5. Once downloade find the ip of your satbox.
    6. Type this into filezilla and the username is root
    7. If you are going to put your c-line in Cccam.cfg open var/etc on filezilla and replace the one Ccam.config file that is there
    8. Download Cccam2.13 and place this in the tmp folder using filezilla
    9. Hit menu/vix/manage local extentions and just install Cccam2.13
    10 Hit men/vix/softcam/ci and start Cccam 2.13 and the tick enable on start up and save.
    Cloud Ibox 4 CCcam Setup
    Key-Tags: Cardsharing, Cardsharing Settings, Cardsharing FAQ

            Category: FAQs Cardsharing     Updated: 30-09-2013, 09:02 by dr.Freak     Views: 10875    Comments: 0
    • 0

    Starview Combo HD

    The Starview Combo HD has the tendency to create "freezing" by itself.

    We recomment to update to the latest firmware which may make it a bit more stable.

    - To prepare the receiver for C@rdSharing please follow the instructions below:

    - Press menu / accessory /network.

    - If you don't see server press 8989.

    - Server -server setup , press ok.

    - You should have 1 off 2 off 3off Up to 8 off

    - Press ok on 1 off

    - Change type to cccam.

    - Name or IP address = First part of code.

    - Port = part 2 of code (5digits)

    - ID = third part of code

    - Password = final part of code

    - Deskey leave blank. You will probably need to change Type cccam to newcamd delete deskey and change back Type to cccam.

    - Press apply.

    - Exit out of everything and should be ok.

    - On name or IP address do not enter C: just enter what follows after.

    - To check status

    - Menu/accessory/network/server

    - You will have on number 01 cccam ****** ****connect If its wrong the same as above but with disconnect

    Cardsharing Settings Starview Combo HD
    Key-Tags: -Cardsharing, Cardsharing Settings Starview Combo HD

            Category: FAQs Cardsharing     Updated: 30-09-2013, 08:58 by dr.Freak     Views: 11944    Comments: 0
    • 40

    Openbox S9 HD

    1. Download the latest firmware upgrade.

    2. If you already have an active CCcam c-lines - Your line will looks like this: C: (IP ADRESS) (PORT) (USERNAME) (PASSWORD)

    3. Then copy/backup into CCcam.cfg file. Otherwise ask us to sent you ready CCcam.cfg file that will include your subscription c-lines.

    4. Copy the 2 files (firmware/CCcam.cfg) that you have to a USB Flash Drive (USB Flash Drive have to be "FAT Format" and files have to be at the Start of drive i.e E: and NOT at any "Folder").

    5. Plug the USB Flash Drive into the back of the receiver.

    6. Setup your Openbox as normal, e.g. sat cable, hdmi or scart cable ,lan, power cable, etc. and turn it on.

    7. On the "Remote control" Press "Menu", scroll down to "Tools" > "Upgrade by USB" (select the firmware .abs file that's on your USB Drive) > "Start"

    8. It will then ask you if you wish to "Burn the Flash" , press "OK" = Yes

    9. The new firmware will now be installed on the box and takes a few mins to complete.

    10. (P.S. Please DON'T follow steps 6. & 7. if your Openbox is already updated with Firmware supports CCcam Emulator)

    11. After receiver reboots ,press "Menu" > "Network Setup" > "Network Setup" and turn "DHCP ON" and Apply.

    12. Then back to the Menu Screen and "Network Setup" and press > "CCcam client setup" > "Update Files by USB".

    13. Select the "CCcam.cfg" and then press "Read" > then Reboot.

    14. Then back to Menu Screen and "Network Setup" > "CCcam client Setup" > "Manage Config Files" > "CCcam.cfg",and Activate all your c-lines (you have to highlight each one and Activate).

    15. Reboot the box and remove the USB

    Cardsharing Settings Openbox S9 HD
    Key-Tags: -Cardsharing, Cardsharing Settings Openbox

            Category: FAQs Cardsharing     Updated: 28-09-2015, 10:09 by dr.Freak     Views: 10939    Comments: 0
    • 0

    Spiderbox 9000HD

    Example: C: 699 argentina server.up4 (IP ADDRESS) 699 (PORT) argentina (USERNAME) server.up4 (PASSWORD)

    1. Press "Menu"

    2. Highlight USB

    3. Scroll down to "Network"

    4. "OK" at 1st one, "Type-on"

    5. Down to "1st server setup" press "OK", "Server 01", "OK", L-R to "CCcam"

    6. Down to "IP" address, "OK", put in the IP ADDRESS. To save press "Menu"- "Save"

    7. Down to "PORT" address, "OK", put in the PORT NUMBER . To save press "Menu"-"Save"

    8. Down to "USERNAME", "OK", put in the USERNAME. To save press "Menu" -"Save"

    9. Down to "PASSWORD", "OK", put in the PASSWORD. To save press "Menu"- "Save"

    10. Down to Press "APPLY", "OK" --- "DONE"

    11. Do the same this other servers Exit all menus.

    Cardsharing Settings on Spiderbox 9000HD
    Key-Tags: Cardsharing Settings, Cardsharing FAQ

            Category: FAQs Cardsharing     Updated: 30-09-2013, 07:58 by dr.Freak     Views: 13327    Comments: 1
    • 0

    Installing a C-Line in a Dreambox

    A. Once you open it, it should look like the photo below. Choose the language of your choice. Login is usually Name: root and Password: dreambox

    1. This is the IP of your Router. It should come up by itself.

    2. This is your Dreambox ( Receiver) IP address. If you don’t know it, press the "Search” button in order to scan and find the IP. Once you enter the IP address, press "Reconnect”.

    3 & 4. These two should be green in order to be able to go further. If one of them is red, then it means that you have either entered the wrong receiver IP address or your receiver is locked.

    B. Once all are green, press "FTP” to move further.

    Cardsharing Settings on Dreambox (CCcam)
    Key-Tags: Cardsharing Settings

            Category: FAQs Cardsharing     Updated: 4-11-2015, 09:36 by dr.Freak     Views: 6300    Comments:
    • 0

    Blade Media BM5000s

    Load in the config file by USB just like before.
    Menu - Setup - Update & Backup - Image Upgrade
    To enter a line manually press "Menu then 9991" on the remote.
    Enter you C or N line details
    Save (Yellow Button)
    Exit out of all of the menus
    You will now need to reboot the box, it doesn't do it automatically

    If you want to enter a line by USB instead of typing in the details
    Open the config file with notepad
    C lines are at the top, N lines near the bottom, depending on what type you are using
    Make sure you paste over the "#" at the start of each line you enter
    Save the changes and put it on your pen drive
    Menu - Setup - Update & Backup - Image Upgrade -Select the config file and reboot the box after it has loaded
    To get the 7 day EPG, put a pen drive into the box or a USB HDD,
    Press EPG on the remote, then download.
    You should now be up and running
    Cardsharing on Blade Media BM5000s
    Key-Tags: Cardsharing Settings, Cardsharing, Cardsharing FAQ

            Category: FAQs Cardsharing     Updated: 4-11-2015, 09:33 by dr.Freak     Views: 6054    Comments:
    • 0

     Ariva 150 CCcam Setup
    DO NOT load any channel file from any other receiever as it will brick you box, only files for ferguson Ariva 150 will work.
    Once you have upgraded the firmware you need your line details. Go to menu then network local settings. Press the red button on remote and you will then see another window. Assuming you are using cccam enter the details as follows.
    URL your server site address
    port what ever port no your server gave you,
    So your details will probably be sent to you like this
    C: port-number username password
    Once entered at bottom off page press connect and you should be in.
    Ariva 150 CCcam Setup
    Key-Tags: Cardsharing, Cardsharing Settings, CCcam

            Category: FAQs Cardsharing     Updated: 25-06-2016, 08:44 by dr.Freak     Views: 28458    Comments: 3
    • 0

     Rules and Penalty for Violation.

    1. It is not allowed to connect to the server without valid subscription. If your subscription has finished or has been paused (suspended), you need to disconnect from the server the same day by deleting the settings you were provided in the billing from your receiver and reboot it. Simply speaking – you need to do an action opposite to the one when you connected to the server for your receiver to stop taking free sockets from the server and stop sending requests for encoding.  Penalty for violation – 5

    2. Cascading is strictly prohibited. It is not allowed to use delayed encoding and encode old records. It is allowed to watch and record simultaneously only 1 channel. It is not allowed PiP option (picture in picture) without pre-paid Dual Login option. It is allowed to send only 1 request for encoding each 10 seconds, 360 – per hour, 8,640 requests per day. Cascading is a theft resulted in banned account without possibility to restore. All your account funds will be abolished. With pre-paid Dual Login, limits will be doubled; it is allowed to use PiP; it is allowed to watch one channel and record the other one at a time.

    3. It is not allowed to use delayed encoding. It is allowed to record programs only with real-time encoding. For the attempt to encode an old record resulting in the cards overload and all other users suffer, your account will be disabled without a possibility to restore, and balance will be nulled and void.

    4. Frequent reconnects to the server will also be punished. Your IP address and account can be banned for very frequent reconnects to the server (>100 per hour) for any reason. Frequent reconnects can be caused by use of the same settings in several locations, error in login or password, sending wrong requests, etc. It’s a desperate measure to protect the server against such micro-attacks.  Penalty for violation – 5

    5. Account can also be disabled for requests with damaged ECM structure your receiver sends to the server. In 70% of the cases, the reason is in a very bad satellite signal and 30% of the cases – in unstable internet connection. Corrupt request will cause the cards reboot and, very often- their irreversible blocking. The result of broken ECM is a picture failure experienced by all users, and, in case of killing the card- monetary expenses. Penalty for violation – 5

    6. It is not allowed to connect to multi-account from various external IP addresses at a time. Multi-account, or so-called multi-room is a possibility of connection of up to 3 receivers per 1 account. This option has been developed only for the families having more than 1 receiver in the flat (or private house). All connections shall be made from a single external IP address, i.e. all receivers shall be physically connected to a single router (modem) of a single provider. Options of the following types: home+office, office+summer cottage, etc. are not allowed. Even short-time connection per 1 account simultaneously from different locations is a rude violation of the rules and is equal to the theft. It is punished by disabling account without the right to restore and deleting balance.

    7. It is not allowed to connect to the server with wrong or not existing login or password. Penalty for violation – 5

    8. It is not allowed to connect to the backup server using different receiver or emulator. Settings for the main and backup server can be used only by one receiver and emulator. If connection to different servers is detected from different receivers, emulators, IP addresses, not to speak of sending different requests to the both servers within one time period, account will be disabled without a possibility to restore and without any compensation. Amount on the balance will be withdrawn and subscription(s) canceled. Freebies, don’t risk, you will fail!

    9. It is not allowed to send EMM requests to the server.  Penalty for violation – 5. For oscam emulator, it is required to add au=0 in oscam.conf file, [dvbapi] section; for cccam emulator, CCcam.cfg file, add (change)DISABLE EMM : yes

    10. It is not allowed to send KeepAlive requests to the server more often than 1 per 5 minutes for each port. Penalty for violation – 5

    11. It is not allowed to connect to any port using more than one emulator. One (1) connection maximum is allowed per each port.  Penalty for violation – 5. Owners of Openbox receiver and its clones have rather frequent problem when adjuster installs, ex. mgcamd emulator, however he does not disable all other emulators available, ex. xcamclient which is importing mgcamd’ settings and starts connecting to the same ports by itself. As a result, emulators are conflicting with each other and the clients see the picture coming and going. If you use mgcamd emulator with Openbox receiver, delete /var/etc/protect/xcam folder necessarily!

    12. Sending duplicated requests for decoding to the server.  Penalty for violation – 5. Requests for decoding is allowed to be sent not frequently than 1 time per 5 seconds.

    13. You can use balance only for buying subscriptions, no refund.

    14. Administration reserves the right to change content of the packages, delete or add channels (packages) without preliminary notification and any compensation.

    15. This is not administration liability, if a problem with provision of services arises not due to a fault of the server (provider bankruptcy, applying new methods of protection by provider, revolution in the country, cyber attack, etc.).

    01. Penalties for rules
    Key-Tags: Cardsharing


    Cardsharing News Archives
    Cardsharing Nordic
        Cardsharing User Cabinet:
        Cardsharing OnLine Stats:
      - not available

      OnLine: 2,     Guests: 1


      crawl Bot      (Today, 19:32:02)

          Last 50 Visits:
      iliasg      (Today, 19:09:21)
      Bilbo123      (Today, 18:58:52)
      dr.Freak      (Today, 18:25:16)
      Gucio      (Today, 17:06:14)
      jamesb      (Today, 16:58:08)
      papichulo911      (Today, 16:53:16)
      izmailov03      (Today, 16:05:32)
      Kuukkeli      (Today, 15:17:59)
      balthazar      (Today, 13:44:58)
      scotty      (Today, 12:08:42)
      Vaclav172      (Today, 11:31:01)
      stanno1      (Today, 11:19:43)
      dzero      (Today, 11:19:05)
      imintz      (Today, 11:02:14)
      pappikos      (Today, 10:58:06)
      vitas4798      (Today, 10:28:00)
      marian1972      (Today, 10:16:16)
      zita1974      (Today, 10:15:05)
      mino23      (Today, 08:11:30)
      Rooobaaat      (Today, 07:46:33)
      dps1979      (Today, 06:23:58)
      willer      (Today, 01:44:07)
      rhis      (05.12.2019, 23:54:36)
      momo14      (05.12.2019, 23:49:48)
      Sane123      (05.12.2019, 23:46:34)
      jane777      (05.12.2019, 23:19:31)
      zoza      (05.12.2019, 21:23:20)
      markopolo1122334455      (05.12.2019, 21:22:16)
      go-mez      (05.12.2019, 21:09:58)
      nayco      (05.12.2019, 21:04:42)
      lummerland      (05.12.2019, 20:21:07)
      wowus      (05.12.2019, 20:15:17)
      mindegy1982      (05.12.2019, 19:46:42)
      como769121      (05.12.2019, 16:56:13)
      NoFear68      (05.12.2019, 16:53:35)
      Lordovi      (05.12.2019, 16:38:09)
      Boongo      (05.12.2019, 16:35:07)
      Knipser1      (05.12.2019, 12:43:38)
      praemolar      (05.12.2019, 11:33:01)
      DAMAZY1971      (05.12.2019, 11:16:23)
      sunproxi      (05.12.2019, 02:39:35)
      kociakto      (05.12.2019, 00:21:17)
      kpepas      (05.12.2019, 00:09:43)
      uelinego      (04.12.2019, 22:19:40)
      pyrokar1987      (04.12.2019, 21:37:51)
      roblasz1      (04.12.2019, 21:23:25)
      randommacguy      (04.12.2019, 21:10:24)
      satcruiser      (04.12.2019, 16:04:40)
      mao631      (04.12.2019, 15:46:03)
      Monika88      (04.12.2019, 15:42:27)


    CardSharing Counter
    HotLog-Stats (since 2019):
    Live-Count (since Jan,2019):
    View Tv-Share Stats
    Cardsharing News Schedule